|
公司基本資料信息
|
|||||||||||||||||||||||||||||||||||
Roasted self drying hardware ink
1、歐帝斯免烘烤自干五金油墨是二液反應型油墨，但它的干燥速度比一般同類型油墨快，有更高的生產效率，對多種物料具有高附著力與高耐濕性、耐溶劑性，特別適合于五金金屬發黑料，，鍍鋅，，304不銹鋼金屬材料；鈦合金以及處理過的聚乙烯、聚丙烯等物料。產品耐*，耐摩擦，耐折彎效果非常好
1. The roasted self drying hardware ink is two liquid reactive ink, but its drying speed is faster than the same type ink. It has higher production efficiency. It has high adhesion and high moisture resistance and solvent resistance to various materials. It is especially suitable for metal metal blackening material, galvanizing, 304 stainless steel metal material; titanium alloy. Gold and processed polyethylene, polypropylene and other materials. The product is resistant to alcohol, friction and bending.
2、油墨調配方法：油墨加配套固化劑15%再加稀釋劑3-10%左右稀釋到印刷適合印刷粘度充分?jǐn)嚢杈鶆?，根?jù)印刷時的實際環境條件選用稀釋劑：快干、中干、慢干稀釋劑，一般情況為冷天（≤15℃）選用快干劑，熱天（≥30℃）選用慢干劑。
2, ink mixing method: ink plus curing agent 15% and diluent 3-10% diluted to print suitable for the printing viscosity full mixing, according to the actual conditions of printing to select diluents: fast dry, dry, slow dry diluent, the general situation for cold days (less than 15 degrees) selected fast drying agent, hot weather (> 30 degrees C) selection Use slow drying agent.
3、干燥時間： 常溫26度10分鐘指觸抹不沾手，完全干透可測試時間時間24小時，低于常溫干燥時間會延長，應急強制干燥：高溫 130度恒溫烘烤20分鐘，等產品冷卻后可以做物理破壞檢測
3, drying time: 26 degrees 10 minutes at normal temperature refers to the touch of non touch hand, completely dry test time and time 24 hours, lower than normal temperature drying time will extend, emergency forced drying: high temperature 130 degrees of constant temperature baking for 20 minutes, and other products can do physical damage detection after cooling test.
4、色澤：26色常用色，其他特殊顏色可以調配；常溫混合固化劑使用時間為8小時內；過期請慎用，加了其他助劑剩余油墨不可回收原未加固化劑油墨中。
4, color: 26 color common color, other special colors can be adjusted; the room temperature mixed curing agent time is 8 hours; expired please prudently, plus other additives remaining ink can not be recycled raw ink.
5、未經試驗不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。
5. No combination of other types of ink can be used without trial. Otherwise, other adhesion, chemical reactions and other bad phenomena are likely to occur.
其他注意事項：
Other notices:
1．各種承印物料的外觀相似，務必確認承印物的材料是否相符，客戶需先試印，確其符合要求后，再批量生產。
1. the appearance of all kinds of printing materials is similar. It is necessary to confirm whether the materials of the substrate are in conformity with each other, and that the customers need to try them out first.
2．印刷前先清除印件表面的塵埃及油漬，可用無水乙醇（*）或抹字水清除，以促進附著效果，在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可;
2. before printing, remove the dust and oil stains on the surface of the printing parts. It can be removed by alcohol or water to promote the effect of attachment. In the process of printing, some slow dry ointments can be properly added, such as drawing or dispersing.
3．溫度低于20度附著力會不穩定，溫度過低將會影響油墨原有的附著力低于10度建議加熱輔助干燥。
3. the adhesion will be unstable if the temperature is below 20 degrees. If the temperature is too low, the adhesion of the ink will be lower than 10 degrees.
4．注意作業車間的濕度，濕度過大會影響附著力，溫度高容易堵網。
4. pay attention to the humidity and humidity of the workshop, which will affect adhesion.
5、使用時注意施工場所的通風狀況良好。盡量避免皮膚直接接觸
5. Attention should be paid to ventilation in the construction site when using. Try to avoid direct skin contact
6、本品不慎濺入口、鼻、眼、耳內，應用大量水清洗或直接求助醫生。
6, this product splashes into the mouth, nose, eyes and ears, and applies a lot of water to clean or seek help from the doctor directly.
7、對本品過敏者，使用前應涂覆一層皮膚扶膚膏或戴不滲透手套。
7. Allergic to this product should be coated with a skin cream or an impermeable glove before use.
8、根據氣候變化，請遠離火源，陰暗處10度-25度環境下密封存放，油墨，稀釋劑嚴禁接觸煙火！
8, according to climate change, please keep away from fire sources, and store in sealed environment at 10 degrees -25 in the shade. Ink and thinner are strictly forbidden to touch fireworks.
淘寶店 搜 歐帝斯油墨
Taobao store inks
以上色漿經SGS檢測符合ROSH標準非醫療標準. 敬告：以上資料記載為本公司實驗室資料數據，僅供參考，不作擔保和承諾依據，大批量生產前需按客戶要求測試合格后方可批量生產，無遵照以上操作方法導致的一切損失本公司一概不負責任！
The above color pulp is measured by the non medical standard of ROSH standard by SGS. The above information is recorded as the company's laboratory data, only for reference, no guarantee and commitment basis. Before large batch production, it is necessary to test the batch production according to the customer's requirements and do not comply with all the losses caused by the above operation methods. No responsibility!
點擊圖片查看原圖
通過認證 
